Quick Overview

Input: RS-485 Modbus RTU
Display: 6-digit, 0.56" (14.2 mm)
Case: Smooth die-cast aluminum explosion-proof
Power: 85-265 VAC or 12-36 VDC
Operating Temperature: -40 to 65°C

Features

Master, slave, or snooper mode
2 form A relays
Linear, square root, or programmable exponent
RS-485 serial communications
Proxy polling for up to 8 process variables
SafeTouch® through-glass button programming
Modbus® RS-485 serial communications
Flanges for wall or pipe mounting

Options

2 form C relays
Isolated 4-20 mA transmitter output

Quick Overview

Input: Process: 0-20 mA , 4-20 mA; ±10 VDC (0-5, 1-5, 0-10 V)
Temperature: Thermocouple J, K, T, E; RTD 100 ? Pt
Display: 4-digit, 1.20" (30.5 mm)
Case: Smooth die-cast aluminum explosion-proof
Power: 85-265 VAC or 12-36 VDC
Operating Temperature: 0 to 65°C

Features

Sunlight readable display
Maximum/minimum display
Linear or square root with low-flow cutoff
Transmitter power option
SafeTouch® through-glass button programming
Modbus® RS-485 serial communications
Flanges for wall or pipe mounting

Options

2 relays or 4-20 mA analog output options
24 VDC transmitter power supply
Dual 24 VDC transmitter power supplies

Quick Overview

Input: Thermocouple J, K, T, E, R, S, B, N, C; RTD 100 ? Pt, 10 ? Cu,
120 ? Ni, 1,000 ? Pt; Modbus PV (slave)
Display: Dual-line 6-digit, 0.60" (15 mm) & 0.46" (12 mm)
Case: Smooth die-cast aluminum explosion-proof
Power: 85-265 VAC or 12/24 VDC option
Operating Temperature: -20 to 65°C

Features

1° or 0.1° resolution
Averages up to 10 RTD sensors
Automatic cold junction compensation
Interlock relays (force on)
SafeTouch® through-glass button programming
Modbus® RS-485 serial communications
Flanges for wall or pipe mounting

Options

SunBright display models
4-20 mA output with isolated 24 VDC @ 40 mA power supply
2 or 4 form C internal relays
External 4-relay & digital I/O expansion modules

Quick Overview

Input: Pulse, open collector, NPN, PNP, TTL, switch contact,
sine wave (coil), square wave, Modbus PV (slave)
Display: Dual-line 6-digit, 0.60" (15 mm) & 0.46" (12 mm)
Case: Smooth die-cast aluminum explosion-proof
Power: 85-265 VAC or 12/24 VDC option
Operating Temperature: -40 to 65°C

Features

Start, batch, & stop with pause front panel buttons
Display batch total + rate, grand total, batch count or preset
Single or multi-stage batching with up to 8 relays
Automatic overflow correction
Manual control or automatic batching
SafeTouch® through-glass button programming
Modbus® RS-485 serial communications
Flanges for wall or pipe mounting
Isolated 24 VDC @ 200 mA transmitter power supply
Total can count up or down

Options

SunBright display models
4-20 mA output with isolated 24 VDC @ 40 mA power supply
2 or 4 form C internal relays
External 4-relay & digital I/O expansion modules

Quick Overview

Input: 0-20 mA, 4-20 mA; ±10 VDC (0-5, 1-5, 0-10 V); Modbus PV (slave)
Display: Dual-line 6-digit, 0.60" (15 mm) & 0.46" (12 mm)
Case: Smooth die-cast aluminum explosion-proof
Power: 85-265 VAC or 12/24 VDC option
Operating Temperature: -40 to 65°C

Features

Start, batch, & stop with pause front panel buttons
Display batch total + rate, grand total, batch count or preset
Single or multi-stage batching with up to 8 relays
Automatic overflow correction
Manual control or automatic batching
SafeTouch® through-glass button programming
Modbus® RS-485 serial communications
Flanges for wall or pipe mounting
Isolated 24 VDC @ 200 mA transmitter power supply
Grand total can count up or down

Options

SunBright display models
4-20 mA output with isolated 24 VDC @ 40 mA power supply
2 or 4 form C internal relays
External 4-relay & digital I/O expansion modules

Features

Displays rate and total simultaneously
Open channel flow with programmable exponent
Isolated 24 VDC @ 200 mA transmitter power supply
32-point linearization with free software
Total, grand total, or non-resettable grand total
SafeTouch® through-glass button programming
Modbus® RS-485 serial communications
Flanges for wall or pipe mounting
Isolated 24 VDC @ 200 mA transmitter power supply

Options

SunBright display models
4-20 mA output with isolated 24 VDC @ 40 mA power supply
2 or 4 form C internal relays
External 4-relay & digital I/O expansion modules

Sunlight Readable Display

All models of the ProtEX-MAX are available with sunlight readable displays. All PD8-765 and PD8-865 models are direct sunlight readable. All other models are available as SunBright display models ("H" model option, ie: PD8-6000-6H7) with an extraordinarily bright LED display for viewing in direct sunlight. The ProtEX-MAX is perfect for applications where the meter is in direct sunlight or in applications where visibility may be impaired by smoke, fog, dust, or distance. There are 8 user selectable intensity levels to choose from on all ProtEX-MAX models.

Through-Glass SafeTouch® Buttons

The PD8 is equipped with up to four sensors that operate as through-glass buttons so that it can be programmed and operated without removing the cover (and exposing the electronics) in a hazardous area. These buttons can be disabled for security by selecting the LOCK setting on the switch located on the connector board in the base of the enclosure. To actuate a button, press one finger to the glass directly over the marked button area. When the cover is removed, mechanical buttons located on the faceplate are used.

Modern, Sleek and Practical Enclosure

The ProtEX-MAX Series has been designed to offer the functions and features of any ProVu®, Trident X2, Snooper, or Vigilante® II model in a great looking explosion-proof housing. However, the PD8 series is not just an 1/8 DIN meter mounted in an explosion-proof housing. A special bezel and electronics were designed exclusively for the ProtEX-MAX. The bezel and faceplate give the front panel a very finished appearance and house the additional electronics for the PD8. Program and operate the meter without opening the housing using the built-in SafeTouch® through-glass button programming or the serial communication port with free Modbus® protocol.

FEATURES
Modern, Sleek and Practical Enclosure
All models available with sunlight readable displays
Display Mountable at 0°, 90°, 180°, & 270° Degrees (Display models)
Explosion-Proof, IP68, NEMA 4X Enclosure
Models Available with ProVu®, Trident X2 , Snooper, or Vigilante® II Functionality
SafeTouch® Through-Glass Button Programming
Password Protection (Select models)
Modbus® RS-485 Serial Communications
Flanges for Wall or Pipe Mounting

Sunlight Readable Display

All models of the ProtEX-MAX are available with sunlight readable displays. All PD8-765 and PD8-865 models are direct sunlight readable. All other models are available as SunBright display models ("H" model option, ie: PD8-6000-6H7) with an extraordinarily bright LED display for viewing in direct sunlight. The ProtEX-MAX is perfect for applications where the meter is in direct sunlight or in applications where visibility may be impaired by smoke, fog, dust, or distance. There are 8 user selectable intensity levels to choose from on all ProtEX-MAX models.

FEATURES
4-20 mA Input
Modern, Sleek and Practical Enclosure
3½ Digits, 1" (25.4 mm) Display
Display Mountable at 0°, 90°, 180°, & 270° Degrees
Easy Calibration and Installation
Loop-Powered Backlight Option
1 V Drop (4 V with Backlight)
Explosion-Proof, IP68, NEMA 4X Enclosure
Flanges for Wall or Pipe Mounting
HART® Protocol Transparent
Operates from -40 to 75°C

General
Display: 3½ digit LCD, 1" (25.4 mm); -1,999 to 1,999
Display Update Rate: 2.5 Updates/Second
Display Orientation: Display may be mounted at 90° increments up to 270° from default orientation
Overrange: Display reads 1 on the left most digit
Programming Method: Four front mounted trim potentiometers accessed when the cover is removed.
Recalibration: Recommended at least every 12 months.
Normal Mode Rejection: 60 dB rejection ratio
Operating Temperature Range: -40 to 75°C
Storage Temperature Range: -40 to 75°C
Relative Humidity: 0 to 90% non-condensing
Connections: Screw terminals accept 12 to 22 AWG wire
Enclosure: Explosion-proof die cast aluminum with glass window, 0.30% max copper content, corrosion resistant epoxy coating, color: blue. NEMA 4X, IP68. Two ¾" NPT threaded conduit openings. One ¾" NPT nickel plated brass conduit plug with 10 mm hex key fitting installed.
Mounting: May be mounted directly to conduit. Two slotted flanges for wall mounting or NPS 1½" to 2½" or DN 40 to 65 mm pipe mounting.
Overall Dimensions: 5.65" x 5.25" x 4.86" (144 mm x 133 mm x 124 mm) (W x H x D)
Weight: 5.00 lbs (80 oz, 2.27 kg)
Warranty: 3 years parts and labor

KEY FEATURES
Informative & Easy to Read Display

The high contrast, backlight LCD display is easy to read from far away and under various lighting conditions. The upper display is 0.7" high and shows 5 digits of flow rate. The lower display is 0.4" high and shows either flow total or a tag with 7 alphanumeric characters. And best of all, the display is mounted right up against the glass so it can be seen from a wide viewing angle.

Through-Glass SafeTouch® Buttons

The PD6830 is equipped with four sensors that operate as through glass buttons so that it can be programmed and operated without removing the cover (and exposing the electronics) in a hazardous area. These buttons can be disabled for security by selecting the LOCK setting on the switch located on the connector board in the base of the enclosure. To actuate a button, press one finger to the glass directly over the marked button area. When the cover is removed, four mechanical buttons located next to the sensors are used.

Modern, Sleek and Practical Enclosure

The first thing customers notice about a product is its enclosure and the ProtEX-RTP really shines here. The copper-free (0.30%), smooth, die-cast aluminum NEMA 4X (IP68) enclosure is finished with a corrosion resistant epoxy coating that literally does make the ProtEX-RTP shine. The built-in mounting flanges make for convenient wall or pipe mounting and there is even a slot on the back of the enclosure for centering on the pipe. There are two ¾" NPT conduit holes for wiring and one ¾" NPT hole for flowmeter connection.

Wide Viewing Angle

Customers can't always look at the display from straight on, so the window and display module have been optimized to provide a wide viewing angle of approximately +/- 40°; nearly twice the competition! Remember, the PD6830 is designed to be looked at.

FEATURES
4-20 mA Input Loop-Powered
5-Digit, 0.7" (17.8 mm) Upper Display
7 Alphanumeric Character, 0.4" (10.2 mm) Lower Display
Loop or External DC-Powered Backlight Standard
SafeTouch® Through-Glass Button Programming
Password Protection
3.0 V Drop without Backlight
Explosion-Proof, IP68, NEMA 4X Enclosure
Flanges for Wall or Pipe Mounting
Linear, Square Root, or Programmable Exponent
Operates from -40 to 75°C
Rate in Second, Minute, Hour, or Day
Open Collector Pulse or Alarm Output

Modern, Sleek and Practical Enclosure
The first thing customers notice about a product is its enclosure and the ProtEX-RTA really shines here. The copper-free (0.30%), smooth, die-cast aluminum NEMA 4X (IP68) enclosure is finished with a corrosion resistant epoxy coating that literally does make the ProtEX-RTA shine. The built-in mounting flanges make for convenient wall or pipe mounting and there is even a slot on the back of the enclosure for centering on the pipe. There are two ¾" NPT conduit holes for wiring.

Isolated Open Collector Output

The isolated open collector output on the PD6820 may be assigned for use with the alarm or totalizer (pulse output). The rating of the output is 30 VDC @ 150 mA max.

FEATURES
4-20 mA Input Loop-Powered
Modern, Sleek and Practical Enclosure
5-Digit, 0.7" (17.8 mm) Upper Display
7 Alphanumeric Character, 0.4" (10.2 mm) Lower Display
SafeTouch® Through-Glass Button Programming
Password Protection
32-Point , Square Root, or Exponential Linearization
Loop or External DC-Powered Backlight Standard
3.0 V Drop (6.0 V with Backlight)
Explosion-Proof, IP68, NEMA 4X Enclosure
Flanges for Wall or Pipe Mounting
HART® Protocol Transparent
Operates from -40 to 75°C

ADDITIONAL FEATURES
Password Protection
A 5-digit password prevents unauthorized changes to the programmed parameter settings. The lock symbol is displayed to show that settings are protected. If the meter is password protected, the meter will display the message LOCKED when the Menu button is pressed.

Alarm Indication
The PD6800 has high or low alarm indication. When in alarm, the display will flash, and a HI or LO symbol is displayed. The alarm has an adjustable deadband (the difference between the set and reset points). The alarm is acknowledged by pressing the ENTER/ACK button.

FEATURES
•4-20 mA Input
•3½+ Digit 0.6" Display
•Easy Four-Button Programming
•NEMA 4X Enclosure
•Programmable Noise Filter
•Loop-Powered Backlight Option
•Max/Min Display
•HART Protocol Transparent
•1.7 V Drop without Backlight
•CSA Certified for -40 to 75°C Operation
(-55 to 75°C with Heater Option)

- 8 Amp Relay Outputs, isolated
- Support for Modbus Slave, Profibus Slave and DeviceNet Slave
- Durus Controllers programming software enables the user to fully simulate the application without the hardware
- The Memory Module enables easy upgrades
- Software is free for downloading from the Web (www.gefanuc.com)
- LCD Backlit display for easy viewing in all environments

Download Product Data Sheet

Download Controller Solutions Data Sheet

For tight spaces, the VersaMax Nano PLC is the perfect solution. Thanks to its all-in-one construction, installation is a breeze. All you have to do is snap it onto a DIN rail or screw it into a panel. With the VersaMax Nano, you save on initial as well as life cycle costs.

The small-footprint VersaMax Micro PLC offers the flexibility of modular design and a variety of built-in features, including up to 64 I/O points (expandable to 170 I/O points), fast cycle times, a robust instruction set and extensive memory that multiplies your programming options.

Download Product Data Sheet

Download Controller Solutions Data Sheet

VersaMax CPUs supply a number of features usually found only in PLCs with larger footprints, including up to 64k of memory for application programs, floating point math, real-time clock, subroutines, PID control, flash memory, and bumpless program store. The serial ports support serial read/write and Modbus master/slave communications.

Download Product Data Sheet

Download Controller Solutions Data Sheet

The VersaMax product family can be used as I/O, as a PLC, and as distributed control for up to 4096 I/O points. With its modular architecture, intuitive features, and unparalleled ease of use, it helps save machine builders and end users time and money.

VersaMax is the first GE Fanuc control product created using the unique Six Sigma design process. Six Sigma combines global research and development techniques, extensive customer needs analysis, and rigorous quality control standards.

The VersaMax I/O and Control product family features a broad selection of I/O modules, terminations, power supplies, and network interface options to enhance your control capability.

Download Product Data Sheet

Download Controller Solutions Data Sheet

VersaPoint accommodates a series of discrete and analog I/O modules with densities from 1 to 16 points. It also supports a host of specialized modules, from RTD and Thermocouple inputs to positioning and counter modules.

Its compact design results in space savings up to 50 percent compared to conventional systems. The modules snap quickly and securely onto a DINrail, and the integrated I/O terminals and internal power bus help reduce wiring by as much as 80 percent.

Download Product Data Sheet

Download Controller Solutions Data Sheet

One reason for the versatility of the Series 90-30 is the large variety of discrete and analog I/O modules (over 100 modules), as well as specialty modules, that are available. In addition, GE Fanuc offers a wide range of high-level communication options, from a simple serial connection to a high-speed Ethernet interface and a number of bus modules.

Download Product Data Sheet

Download Controller Solutions Data Sheet

The Series 90-70 Features:

- Open architecture based on the VME-bus standard
- Redundancy for critical applications when combined with Genius* I/O – Genius Modular Redundancy (GMR) systems and Hot Standby systems
- A wide variety of communications options including Ethernet TCP/IP, reflective memory, Genius LAN and serial communications modules

Download Product Data Sheet

Download Controller Solutions Data Sheet

The RX3i features A high performance controller with a 300 MHz Intel® microprocessor and 10 Mbytes of user memory that eliminates the need for multiple controllers and simplifies control.

A universal backplane with a highspeed PCI bus running at 27 MHz for fast data throughput for complex I/O and a serial bus for simple I/O that optimizes performance and your investment. The universal backplane also supports HOT SWAP to minimize downtime.

A wide range of I/O modules (over 40 types available) for simple to complex applications; various network modules are also available.

The PACSystems portable control engine provides high performance on several different platforms, allowing OEMs and end users with application variability to choose the exact control system hardware that best suits there needs - all in a single, compact and highly integrated package.

Download Product Data Sheet

Download PACSystems Data Sheet

The RX7i Features Pentium® CPUs for your every need, from Celeron 300mHz to M Class 1.8 Ghz
A VME64 Backplane providing up to four times the bandwidth of existing Series 90-70 systems
10/100 Ethernet built into the CPU, with easy cabling RJ-45 dual ports connected through an auto-sensing switch, so there is no need for additional switches or hubs rack to rack

Up to 64 MB memory for fast execution, storage of the complete program with all documentation—all in one CPU

Supports existing Series 90-70 modules and expansion racks, VME modules and GENIUS networks— protecting your hardware investment.

Download Product Data Sheet

Download PACSystems Data Sheet