The SEM203 in-head transmitter incorporates the latest digital technology to ensure accurate drift free linearisation. It connects to an appropriate sensor and converts the output to a linear 4-20mA output signal, providing a level of performance at a cost that was not possible with earlier analogue types.

High accuracy and stability coupled with the flexibility of reduced stock holding and the quick and easy way of bench re-ranging makes the SEM203 the ideal choice for the majority of temperature sensing requirements.

The SEM203 is linearised to comply with all common RTD sensor standards i.e. 0.00385, 0.003916 etc. all common thermocouple types and 2252 ohms and 10k ohms YSI Thermistors, and up to 10k ohms potentiometers.

An on board LED indicates the successful completion of the range programming and also provides an instant indication of sensor health.

*Low Cost
*10 Year Warranty
*Push Button Calibration
*RTD, T/C, Slidewire or Thermistor Input
*Drift Free Linerisation
*Re-Rangeable without PC
*LED Over-Range Indication
*Galvanic Isolation on T/C Types

Download Product Data Sheet

The SEM203 in-head transmitter incorporates the latest digital technology to ensure accurate drift free linearisation. It connects to an appropriate sensor and converts the output to a linear (4 to 20) mA output signal, providing a level of performance at a cost that was not possible with earlier analogue types.

High accuracy and stability coupled with the flexibility of reduced stock holding and the quick and easy way of bench re-ranging makes the SEM203 the ideal choice for the majority of temperature sensing requirements.

The SEM203 is linearised to temperature to comply with all common thermocouple types.

An on board LED indicates the successful completion of the range programming and also provides an instant indication of sensor health.

- K, J, N, E, T,R, S thermocouples plus mV
- Simple push button configuration
- Advanced user configuration for access to 56 pre-set temperature ranges
- Push button user trim
- Programmable burnout
- Galvanic Isolation
- 10 Year Warranty

Download Product Data Sheet

PC configuration allows the user to select Range, units and Burnout direction, without requiring calibration equipment. Configuration is performed quickly using our new USB port driven configurator by simply connecting two clips to the SEM206/P loop terminals and following the software instructions. Calibration set up may be saved as a file on the PC for later use.

The SEM206/P in head transmitter incorporates the latest digital technology to ensure accurate drift free performance. If required the desired range can be specified at the time of order, removing the need for user configuration. If the range is not specified then the transmitter will be shipped with the default range of 0 to 100 °C

- Configuration using USB port powered configurator
- Configurable in seconds
- High stability
- Over range LED indication
- Programmable burnout
- 10 year warranty

Download Product Data Sheet

PC configuration allows the user to select TC type, Range, units and Burnout direction, without requiring calibration equipment. Configuration is performed quickly using a our new USB port driven configurator by simply connecting two clips to the SEM206TC loop terminals and following the software instructions. Calibration set up may be saved as a file on the PC for later use.

The SEM206 TC in head transmitter incorporates the latest digital technology to ensure accurate drift free performance. If required the desired range can be specified at the time of order, removing the need for user configuration. If the range is not specified then the transmitter will be shipped with the default range of 0 to 1000 °C type K.

- K, J, N, E, T, R, S thermocouples plus mV
- Configuration using USB port powered configurator
- Isolated input
- Over range LED indication
- Programmable burnout

Download Product Data Sheet

Output range and other operating parameters are easily programmed using RCPW software running under "Windows" without the need for re-calibration.

Isolation is a standard feature to overcome any potential ground loop effects. Two microprocessors operate together to ensure error-free transmission across the isolation barrier.

A sensor referencing facility enables the transmitter to be accurately matched to a particular sensor.

- 10 Year Warranty
- Galvanically Isolated
- Universal Input
- Versions for Hazardous Areas
- High Accuracy and Stability
- Sensor Referencing
- Easily Re-programmed
- In Head Mounting

Download Product Data Sheet

PC configuration allows the user to select TC type, Range, Filter, units, linearization and burnout direction, without requiring calibration equipment. Additionally, the user may read live process data when connected to the PC, this allows for sensor offset, and output alignment calibration, where the user can enter values to match the actual process and therefore reducing system errors. Other sensor characteristics or your own 22 point linearisation characteristic (for mV signals) can be downloaded into the product allowing you to adapt it exactly to your application.

PC configuration allows the user to select RTD type, Range, Filter, units, linearization and Burnout direction, without requiring calibration equipment. Additionally, the user may read live process data when connected to the PC, this allows for sensor offset, and output alignment calibration, where the user can enter values to match the actual process and therefore reducing system errors.

The TTR200 is mounted using two 5.5 mm holes, on standard 33 mm fixing
centres and will fit a DIN standard termination head.The TTR200 must be installed with adequate protection from moisture andcorrosive atmospheres.Enclosure colour grey.Labels - Two product identification labels indicate Serial number , Model,Input Type Range.Connection label indicates output +/- terminals and (1 to 3) Input terminals.

The SEM310 has full HART communications protocol which allows the user to quickly and easily download information or interrogate the device.

A sensor referencing facility enables the transmitter to be accurately matched to a particular sensor.

- 10 Year Warranty
- HART Protocol
- Universal Input
- Versions for Hazardous Areas
- Sensor Burnout Detect
- Isolation to 500 VAC
- Spring Mounting

Download Product Data Sheet

A simple push button operation allows the user to select RTD type, Burnout direction, Select fixed ranges and trim 4 and 20 Ma points.

The SEM213P transmitter incorporates the latest digital technology to ensure accurate drift free performance.

If required the desired range can be specified at the time of order, removing the need for user configuration. If the range is not specified then the transmitter will be supplied at the default range of (0 to 100) °C type Pt100 IEC.

- Pt100 (3 Types), Ni100, Ni120, Cu100, Ohms (10 To 400_)
- Simple Push Button Configuration
- Advanced User Config For Access To 56 PreSet Temperature Ranges
- User Push Button Trim
- Programmable Burnout

Download Product Data Sheet

A simple push button operation allows the user to select TC type, Burnout direction, Select fixed ranges and trim 4 and 20 mA points. The SEM213TC transmitter incorporates the latest digital technology to ensure accurate drift free performance.

If required the desired range can be specified at the time of order, removing the need for user configuration. If the range is not specified then the transmitter will be supplied at the default range of (0 to 1000) °C type K.

K, J, N, E, T, R, S Thermocouples Plus mV

- Simple Push Button Configuration
- Advanced User Config for Access to 56 Pre Set Temperature Ranges
- User Push Button Trim
- Programmable Burnout

Download Product Data Sheet

It has been designed to accept most common process and temperature sensor inputs and provide the user with a standard two wire (4 to 20) mA output signal. Isolation is provided between input and output and all temperature ranges are linear to temperature. The addition of a display provides the user with instant information of the loop condition at the point of measurement. It comes in either our SCH4 ABS plastic connector head or our new SCH15 Stainless steel connector head.
Designed for ease of use, our latest USB interface is fitted for quick and easy configuration. Just connect a standard USB cable between the SEM710 and your PC. Using our free configuration software, your PC will automatically upload the existing configuration data and guide you through any changes you wish to make. To further help save time, the SEM710 does not need to be wired to a power supply during the configuration process, it is powered via the USB interface from your PC.

-Simple configuration via USB port
- Isolated PT100, thermocouple input
- Display temperature in °C /°F or output drive in mA
- Push button user trim
- (4 to 20) mA two wire output
- Housing ABS plastic or stainless steel
- 10 year warranty

Download Product Data Sheet

Designed for ease of use, this range is configured with our USB port powered configuration module. The module interfaces a PC USB port to the SEM1603, using the (4 to 20) mA loop to communicate. Using our free configuration software, you will be able to read the current configuration data, and then perform any changes you wish to make to the configuration. To further help save time, the SEM1603 and configuration module do not need to be wired to a power supply during the configuration process, both are powered by the USB interface on your PC.

- Configuration using USB port powered configurator
- PT100 input
- Isolated input
- Input linear to temperature
- (4 to 20) ma two wire output
- 10 year warranty

Download Product Data Sheet

Designed for ease of use, this range is configured with our USB port powered configuration module. The module interfaces a PC USB port to the SEM1603, using the (4 to 20) mA loop to communicate. Using our free configuration software, you will be able to read the current configuration data, and then perform any changes you wish to make to the configuration. To further help save time, the SEM1603 and configuration module do not need to be wired to a power supply during the configuration process, both are powered by the USB interface on your PC.

- Configuration using USB port powered configurator
- Thermocouple / mV
- Isolated input
- Input linear to temperature
- (4 to 20) ma two wire output
- 10 year warranty

Download Product Data Sheet

The SEM315 has full HART communications protocol which allows the user to quickly and easily down-load information or interrogate the device enabling the following:-

- Simple re-ranging of sensor type and range
- Easy on site re-calibration
- Self documentation
- Operation with proprietary software packages such as AMS Plant Web™ and Cornerstone™
- Remote configuration on the (4 to 20) mA loop with a hand held communicator or with a PC & HART modem
- Online Digital communication concurrent with a (4 to 20) mA Analogue signal.
All the standard HART universal and common usage commands are fully implemented, with other device specific commands that enable access to the enhanced performance parameters of the SEM315.

- 10 Year Warranty
- HART® Protocol
- Universal Input
- Sensor Burnout Detect
- Isolation to 500 VAC

Download Product Data Sheet

Designed for ease of use, our USB interface is fitted for quick and easy configuration. Just connect a standard USB cable between the SEM1610 and your PC and you’re ready to go. Using our free configuration software, your PC will automatically read the current configuration data and guide you through any changes you wish to make. To further help save time, the SEM1610 does not need to be wired to a power supply during the configuration process, it is powered via the USB interface from your PC.

The software allows the user to set factory default settings.

The SEM1610 is also provided with user push button trim, allowing trim adjustments at both 4 mA and 20 mA. The user trim function can be locked during configuration if not required. The range led indicates out of range input during normal operation, during user trim it is used to indicate the stage of trim.

As the SEM1610 case design is based on the DIN43880 standard, a wide range of are available to the user, offering both visible and user access to the front panel functions.

- Simple USB Configuration Port
- Universal Pt100,Thermocouple, mV, mA Input
- Push Button User Trim
- 4/20mA two wire Output
- 10 Year Warranty

Download Product Data Sheet

• Duct temperature transmitter, TG100 type
• Measuring ranges from 0 to +50°C, -20 to +80°C, -50 to +50°C, 0 to +100°C,
0 to 200°C, 0 to +300°C, 0 to +400°C (according to model, see “Configuration”)
• 0-10 V output , active sensor, power supply 24 Vac/Vdc (3-4 wires) or
4-20 mA output , passive loop, power supply 18 to 30 Vdc (2 wires)
• ABS IP 65 housing, with or without display
• Quick and easy mounting “1/4 turn” system with wall-mount plate

Measuring range ......................see chart ”Configuration”
Units of measurement .............°C, °F
Accuracy * ................................±0,5% of reading ±0,4°C (duct mount probe)
according to the probe (Pt 100 on terminal block)
Response time .........................1/e (63%) 5 sec. (duct mount probe)
according to the probe (Pt 100 on terminal block)
Resolution ................................0,1°C
Type of sensor..........................Pt 100 class A as per DIN IEC751
Type of fluid............................ air et neutral gases

Download Product Data Sheet

• Ranges from 0-100%RH and -40 to +180°C (probe dependent)
• Configurable intermediate ranges
• Functions : relative and absolute humidity, dew point, wet and
dry temperature, enthalpy.
• Smart-Pro system interchangeable probes (PC or Stainless Steel)
• On-site calibration
• Simultaneous display of 2 parameters
• 2 outputs 4-20 mA or 0-10V (4 wires), RS 232, 2 RCR relays 6A/230 Vac
• 2 visual (dual color LED) and audible (buzzer) alarms
• Output diagnostics
• ABS IP 65 housing, with or without 2-line backlit display.
• Quick and easy mounting using the “1/4 turn” system with wall-mounting plate.

Humidity
Measuring range.................................0 to 100 %RH
Units of measurement........................%RH
Accuracy*(Repeatability, linearity, hysteresis) ±1,5%RH (from 3 to 98%RH and if 15°C T 25°C)
Temperature dependence..................±0.04 x (T-20)%RH (if T<15°C or T>25°C)
Response time ....................................<10 sec. (from 10% RH to 80%RH, V =2m/s) air
Resolution ...........................................0,1 %RH
Factory calibration uncertainty .........±0.88%RH
Type of sensor ....................................capacitive
Type of fluid.........................................air and neutral gases (high resistance to solvents)

Temperature
Measuring range.................................from -20 to +120°C ( polycarbonate probe)
from -40 to +180°C (st.steel probe)
Units of measurement........................°C, °F
Accuracy *...........................................±0,3% of reading ±0,25°C
Response time.................................... t = 9 sec. for V = 1 m/s 0,9 air
Resolution...........................................0,1°C
Type of sensor....................................Pt 100 1/3 as per DIN IEC 751
Type of fluid ........................................air and neutral gases

Download Product Data Sheet

• Ranges from 0-100%RH and -40 to +180°C (probe dependent)
• Configurable ranges
• Functions : relative and absolute humidity, dew point, wet and
dry temperature, enthalpy.
• Smart-Pro interchangeable probes (PC or stainless steel)
• On-site calibration
• Simultaneous display of 1 to 4 parameters
• External transmitter inputs (KIMO Class 200 and 300)
• 2 outputs 4-20 mA (4 wires) or 0-10V, RS 232, 2 RCR relays 6A/230 Vac
• 2 visual alarms (dual color LED) and audible alarm (buzzer - 80 dB)
• Output diagnostics
• MODBUS network RS 485 system (optional)
• ABS or ALU IP 65 housing, with or without backlit graphic display.
• Quick and easy mounting using “1/4 turn” system with wall-mounting plate.

Humidity
ALU or ABS housing
WITH or WITHOUT display
TH300
remote probe
TH300
standard
• Ranges from 0-100%RH and -40 to +180°C (probe dependent)
• Configurable ranges
• Functions : relative and absolute humidity, dew point, wet and
dry temperature, enthalpy.
• Smart-Pro interchangeable probes (PC or stainless steel)
• On-site calibration
• Simultaneous display of 1 to 4 parameters
• External transmitter inputs (KIMO Class 200 and 300)
• 2 outputs 4-20 mA (4 wires) or 0-10V, RS 232, 2 RCR relays 6A/230 Vac
• 2 visual alarms (dual color LED) and audible alarm (buzzer - 80 dB)
• Output diagnostics
• MODBUS network RS 485 system (optional)
• ABS or ALU IP 65 housing, with or without backlit graphic display.
• Quick and easy mounting using “1/4 turn” system with wall-mounting plate.

Humidity
Measuring range .......................................0 to 100 % RH
Units of measurement ..............................% RH
Accuracy*(Repeatability, linearity, hysteresis) ......±1,5%RH (from 3 to 98%RH and if 15°C T 25°C)
Temperature dependence ........................±0.04 x IT-20I%RH (if T<15°C or T>25°C)
Response time ..........................................<10 sec. (from 10% RH to 80%RH, Vair=2m/s)
Resolution .................................................0,1 % RH
Factory calibration uncertainty ...............±0.88%RH
Type of sensor ..........................................capacitive
Type of fluid ...............................................air and neutral gases (high resistance to solvents)

Temperature
Measuring range .......................................from -20 to +120°C (polycarbonate probe)
from -40 to +180°C (stainless steel probe)
Units of measurement ..............................°C, °F
Accuracy * .................................................±0,3% of reading ±0,25°C
Response time .......................................... t = 9 sec. for V = 1 m/s 0,9 air
Resolution .................................................0,1°C
Type of sensor...........................................Pt 100 1/3 selon DIN IEC 751
Type of fluid...............................................air and neutral gases

Download Product Data Sheet

• Temperature transmitter type TM 50/51
• Pt100 3 wires output or Pt1000 2 wires (according to the model)
• ABS IP65 and IP 30 housing, without display
• Quick and easy mounting “1/4 turn” system with wall-mount plate

Measuring range...........................-20 to +80°C (air tight and duct mount model)
+10 à +40°C (ambient model)
Accuracy......................................Pt100 class A as per DIN IEC751
Pt1000 class A as per DIN IEC751
Response time..............................1/e (63%) 5 sec. (ambient model) 1/e (63%) 20 sec. (air tigth model) depending on the probe (Pt100 on terminal block)
Type of fluid..................................air and neutral gases

Download Product Data Sheet

• Temperature transmitter type TM100.
• Measuring ranges from 0 to +50°C, -20 to +80°C, -50 to +50°C,
0 to 100°C (see “Configuration”)
• 0-10 V or 4-20 mA output, active sensor, power supply 24 Vac/Vdc (3-4 wires)
or 4-20 mA output , passive loop, power supply 18 to 30 Vdc (2 wires).
• ABS IP 65 and IP 30 housing, with or without display.
• Quick and easy mounting “1/4 turn” system on wall-mount plate.

Measuring range ..................................0 to +50°C, -20 to +80°C, -50 to +50°C, 0 to +100°C
Units of measurement .......................°C, °F
Accuracy * ..........................................±0,5% of reading ±0,4°C
Response time ...................................1/e (63%) 5 sec. (ambient)
1/e (63%) 20 sec. (air tight)
Resolution ..........................................0,1°C
Type of sensor....................................Pt 100 class A as per DIN IEC751
Type of fluid........................................air and neutral gases

Download Product Data Sheet

Update time 200 mSResponse Time 0.5 seconds
Start up time 1 seconds ( Vout 0.0 V duringstart up)
Power Supply (12 to 30) Volts dc
Warm-up Time 1 Minute
Download Product Data Sheet

The SEM110P accepts a Pt100 platinum resistance temperature sensor to BS1 904 or DIN 43760 standards or a thermocouple K, T, J, R or S and converts the sensor temperature to a current varying between 4 and 20 mA. Version are also available for slide wired (W), variable resistor (Z) or temperature deferential (D). The same two wires that power the transmitter also carry the transmission current such that only two connections are required. This drastically reduces installation and wiring costs whilst the nature of current transmission provides superb nose immunity and ensures that line impedance's, thermoelectric effects etc. do not introduce errors.

Transmitters are factory calibrated to the desired range within the accuracy stated, however, SPAN and ZERO potentiometers are available for periodic recalibration or for 'tweaking' out sensor errors when used with two wire or low grade detectors.

Configuration is performed quickly using our new USB port driven configurator by connecting the transmitterto the configurator and following the software instructions. The software allows you to tag the device, set installation date and set output range. Either fixed ranges or your own custom ranges can be configured for all output types in °C or °F.

The 4 digit LED display option provides you with a visual indication of the process parameters, the display may be set to indicate either humidity, temperature, dew point or toggle between all three parameters.

Using our popular SCH4 connection head, the SEM162 series can be ordered for duct, wall or remote sensor mounting.

Configuration is performed quickly using our new USB port driven configurator by connecting the transmitterto the configurator and following the software instructions. The software allows you to tag the device, set installation date and set output range. Either fixed ranges or your own custom ranges can be configured for all output types in °C or °F.

The 4 digit LED display option provides you with a visual indication of the process parameters, the display may be set to indicate either humidity, temperature, dew point or toggle between all three parameters.

Using our popular SCH4 connection head, the SEM162 series can be ordered for duct, wall or remote sensor mounting.

FEATURES
•Temperature Transmitters
•Universal Input: RTD, TC, Ohm & mV Inputs
•Rugged General Purpose Models
•330° Rotatable Backlit LCD
•Display PV, Input Type, Eng Units & Bargraph
•Galvanic Isolation Prevents Ground Loops
•Wide Voltage Range: 10.5 to 45 VDC
•Wide Operating Temperature Range
•Protection Heads & Thermowells Available
•Order Factory Configured, Ready to Install*

FEATURES
•Temperature Transmitters
•Universal Input: RTD, TC, Ohm & mV Inputs
•Rugged General Purpose Models
•330° Rotatable Backlit LCD
•Display PV, Input Type, Eng Units & Bargraph
•Galvanic Isolation Prevents Ground Loops
•Wide Voltage Range: 10.5 to 45 VDC
•Wide Operating Temperature Range
•Protection Heads & Thermowells Available
•Order Factory Configured, Ready to Install*

FEATURES
•Temperature Transmitters
•Universal Input: RTD, TC, Ohm & mV Inputs
•Rugged General Purpose Models
•330° Rotatable Backlit LCD
•Display PV, Input Type, Eng Units & Bargraph
•Galvanic Isolation Prevents Ground Loops
•Wide Voltage Range: 10.5 to 45 VDC
•Wide Operating Temperature Range
•Protection Heads & Thermowells Available
•Order Factory Configured, Ready to Install*

FEATURES
•Temperature Transmitters
•Universal Input: RTD, TC, Ohm & mV Inputs
•Rugged General Purpose Models
•330° Rotatable Backlit LCD
•Display PV, Input Type, Eng Units & Bargraph
•Galvanic Isolation Prevents Ground Loops
•Wide Voltage Range: 10.5 to 45 VDC
•Wide Operating Temperature Range
•Protection Heads & Thermowells Available
•Order Factory Configured, Ready to Install*

• Temperature and air velocity transmitter type CTV100.
• Ranges from 0-5 m/s to 0-30 m/s and 0 to +50°C, -20 to +80°C, -50 to +50°C, 0 to
+100°C (see "Configuration")
• 0-10 V or 4-20 mA output, active, power supply 24 Vac/Vdc (3-4 wires)
• ABS IP 65 housing, with or without display
• Alternating display of air velocity and temperature
• Quick and easy mounting “1/4 turn” system with wall-mount plate

Air Velocity
Measuring range ..................0 to 5m/s,0 to 10m/s, 0 to 15m/s, 0 to 20m/s, 0 to 30m/s
Units of measurement .........m/s and fpm
Accuracy * ............................±3% of reading ±0,3 m/s
Response time .....................1/e (63%) 2 sec.
Resolution ............................0,1 m/s
Type of fluid..........................air and neutral gases

Temperature
Measuring range...................................0 to +50°C, -20 to +80°C,-50 to +50°C,0 to +100°C
Units of measurement .......................°C, °F
Accuracy * ..........................................±0,5% of reading ±0,4°C
Response time ...................................1/e (63%) 5 sec.
Resolution ..........................................0,1°C
Type of sensor....................................Pt100 class A as per DIN IEC751
Type of fluid........................................air and neutral gases

Download Product Data Sheet